Victron Orion-Tr Smart 12V to 12V 30Amp (360W) DC to DC Battery Charger Isolated. The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.
Victron Orion-TR smart 30-amp, 12 to 12-volt DC-DC isolated battery charger fully programmable with BlueTooth interface and free Victron Connect app.
The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with Built-In Bluetooth.
Watch Our Videos to Learn More
The Orion Smart DC-DC chargers can be used as a power supply or as a battery charger. In charger mode the three-state charge algorithm will increase battery life by properly charging the battery. Especially in the case of vehicles with a smart alternator, or voltage drop caused by long cable runs, controlled charging is indispensable. Controlled charging will also protect the alternator in lithium systems where direct charging can overload the alternator due to the low impedance of the lithium battery. In fixed output mode the output voltage will remain stable independent of the applied load or varying input voltage (within the specified range).
Comes with Free Shipping Australia Wide
The Orion Smart DC-DC charger can be set up to only provide power when the engine is running. This is possible thanks to the built-in engine shutdown detection. This also prevents the onboard voltage of the vehicle from becoming too low. It is not necessary to intervene in the system of the vehicle, to install a separate motor run sensor or to intervene in the CAN-bus system. Apart from this detection, the Orion Smart DC-DC charger can also be activated by a forced allowed to charge feature, e.g. connected to the ignition switch.
Bluetooth Smart Built-In
Any Bluetooth enabled Apple or Android smart phone, tablet or other device can be used to monitor, change settings and to update the charger when new software features become available via the VictronConnect App.
All models are short circuit proof and can be paralleled to increase output current- An unlimited number of units can be connected in parallel.
High Temperature Protected-The output current will reduce at high ambient temperature.
IP43 Protection- When installed with the screw terminals oriented downwards.
Screw terminals- No special tools needed for installation.
Bluetooth Smart Enabled- Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.
Adaptive 3-Stage Charge Algorithm: Bulk – Absorption – Float- For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
For lithium batteries absorption time is fixed, default 2 hours.Alternatively, a fixed output voltage can be chosen.
Remote on-off- A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
Smart Alternator Compatibility
Vehicle manufacturers are now introducing smart ECU (Engine Control Unit) controlled alternators to increase fuel efficiency and reduce emissions. Smart alternators deliver a variable output voltage and are shut down when they’re not needed. The converter has a engine running detection mechanism. This prevents the converter from discharging the starter battery when the alternator does not supply power. The Orion-Tr Smart Isolated DC-DC charger separates the starter battery from the service battery when the engine is not running.
*Please Note: A 60A circuit protection is required on both sides of the unit (start battery and auxiliary battery). Minimum cable size is 10mm2.
No Solar Regulator in the DC-DC Charger:
Victron have chosen to separate the charger and the solar regulators, these are the advantages:
You can choose the correct solar regulator to match your panels with the best efficiency for the solar charging.
The solar can be charging into the battery system simultaneously with the onboard vehicle charging
Without a solar regulator, the DC-DC charger will stay cheaper
Bluetooth Smart Enabled: Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available
Remote on-off: A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two–pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
All models are short circuit proof and can be paralleled to increase output current: An unlimited number of units can be connected in parallel.
High Temperature Protected: The output current will reduce at high ambient temperature.
IP43 Protection:When installed with the screw terminals oriented downwards.
Screw Terminals: No special tools are needed for installation.
The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for lead acid and lithium batteries. Models are available up to 400W, and unlimited multiple units can be connected in parallel to increase output power. All you need to do is plug it in, clip it on and turn it on. That’s it. Set and forget. They will never overcharge and are compatible with common automotive batteries including lithium (LiFeP04).
REMOTE ON/OFF
Use the remote function to enable and disable the converter remotely with the remote on/off connector or using the VictronConnect app. Typical use cases include a user operated hard wired switch and automatic control by for example a Battery Management System.
ELECTRONIC PROTECTION
Over-temperature protection and power derating when temperature is high. Overload protected. Short circuit protected. Connector over-temperature protection. An unlimited number of units can be connected in parallel to increase charging amps.
SAFE & LIGHTWEIGHT
Can be Paralleled to increase output current. An unlimited number of units can be connected in parallel.
LCD POWER READOUTS
Battery meter makes it easy to see the status of your battery
EASY TO USE
A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
TEMPERATURE PROTECTION
The output current will reduce at high ambient temperature.
IP43 Protection
When installed with the screw terminals oriented downwards.
Either unit can be used for systems that don’t require isolation, but the non-isolated requires one less wire to be installed.
One example of a non-isolated system is an automotive system, such as both batteries are negative and connected to the chassis of a vehicle. The system is non-isolated but either unit will suit.
The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to °C with a full rated output up to 40°C.
NEED TO CALCULATE MPPT USE THE HANDY TOOL BELOW
Australian Owned & Operated
Designed for Off Road and Heavy Duty Applications
Perfect for use in caravans, marine, camping and home storage off grid applications. Solar, wind or battery charger compatible. Designed to handle the vibration when off road.
Reliable 12V Power
Campers appreciate being able to charge multiple devices simultaneously while enjoying a peaceful camping experience.
Portable Power Solutions
Superior Versatility: This MPPT is ideal for 4WDs, caravans, RVs, trucks, campers, trailers, campervans, commercial vehicles and boats.
Easy to Use and Setup
This plug-and-play device is so user-friendly that anyone can set it up. Multiple Protection: Over-charge, short circuit, over-temperature, over-voltage, solar input overload and reverse polarity protection are incorporated.
For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
For lithium batteries absorption time is fixed, default 2 hours.
Alternatively, a fixed output voltage can be chosen.
Victron Orion-Tr Smart 12V to 12V 30Amp (360W) DC to DC Battery Charger Isolated. The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.
Victron Orion-TR smart 30-amp, 12 to 12-volt DC-DC isolated battery charger fully programmable with BlueTooth interface and free Victron Connect app.
The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with Built-In Bluetooth.
Watch Our Videos to Learn More
The Orion Smart DC-DC chargers can be used as a power supply or as a battery charger. In charger mode the three-state charge algorithm will increase battery life by properly charging the battery. Especially in the case of vehicles with a smart alternator, or voltage drop caused by long cable runs, controlled charging is indispensable. Controlled charging will also protect the alternator in lithium systems where direct charging can overload the alternator due to the low impedance of the lithium battery. In fixed output mode the output voltage will remain stable independent of the applied load or varying input voltage (within the specified range).
Comes with Free Shipping Australia Wide
The Orion Smart DC-DC charger can be set up to only provide power when the engine is running. This is possible thanks to the built-in engine shutdown detection. This also prevents the onboard voltage of the vehicle from becoming too low. It is not necessary to intervene in the system of the vehicle, to install a separate motor run sensor or to intervene in the CAN-bus system. Apart from this detection, the Orion Smart DC-DC charger can also be activated by a forced allowed to charge feature, e.g. connected to the ignition switch.
Bluetooth Smart Built-In
Any Bluetooth enabled Apple or Android smart phone, tablet or other device can be used to monitor, change settings and to update the charger when new software features become available via the VictronConnect App.
All models are short circuit proof and can be paralleled to increase output current- An unlimited number of units can be connected in parallel.
High Temperature Protected-The output current will reduce at high ambient temperature.
IP43 Protection- When installed with the screw terminals oriented downwards.
Screw terminals- No special tools needed for installation.
Bluetooth Smart Enabled- Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.
Adaptive 3-Stage Charge Algorithm: Bulk – Absorption – Float- For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
For lithium batteries absorption time is fixed, default 2 hours.Alternatively, a fixed output voltage can be chosen.
Remote on-off- A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
Smart Alternator Compatibility
Vehicle manufacturers are now introducing smart ECU (Engine Control Unit) controlled alternators to increase fuel efficiency and reduce emissions. Smart alternators deliver a variable output voltage and are shut down when they’re not needed. The converter has a engine running detection mechanism. This prevents the converter from discharging the starter battery when the alternator does not supply power. The Orion-Tr Smart Isolated DC-DC charger separates the starter battery from the service battery when the engine is not running.
*Please Note: A 60A circuit protection is required on both sides of the unit (start battery and auxiliary battery). Minimum cable size is 10mm2.
No Solar Regulator in the DC-DC Charger:
Victron have chosen to separate the charger and the solar regulators, these are the advantages:
You can choose the correct solar regulator to match your panels with the best efficiency for the solar charging.
The solar can be charging into the battery system simultaneously with the onboard vehicle charging
Without a solar regulator, the DC-DC charger will stay cheaper
Bluetooth Smart Enabled: Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available
Remote on-off: A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two–pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
All models are short circuit proof and can be paralleled to increase output current: An unlimited number of units can be connected in parallel.
High Temperature Protected: The output current will reduce at high ambient temperature.
IP43 Protection:When installed with the screw terminals oriented downwards.
Screw Terminals: No special tools are needed for installation.
The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for lead acid and lithium batteries. Models are available up to 400W, and unlimited multiple units can be connected in parallel to increase output power. All you need to do is plug it in, clip it on and turn it on. That’s it. Set and forget. They will never overcharge and are compatible with common automotive batteries including lithium (LiFeP04).
REMOTE ON/OFF
Use the remote function to enable and disable the converter remotely with the remote on/off connector or using the VictronConnect app. Typical use cases include a user operated hard wired switch and automatic control by for example a Battery Management System.
ELECTRONIC PROTECTION
Over-temperature protection and power derating when temperature is high. Overload protected. Short circuit protected. Connector over-temperature protection. An unlimited number of units can be connected in parallel to increase charging amps.
SAFE & LIGHTWEIGHT
Can be Paralleled to increase output current. An unlimited number of units can be connected in parallel.
LCD POWER READOUTS
Battery meter makes it easy to see the status of your battery
EASY TO USE
A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
TEMPERATURE PROTECTION
The output current will reduce at high ambient temperature.
IP43 Protection
When installed with the screw terminals oriented downwards.
Either unit can be used for systems that don’t require isolation, but the non-isolated requires one less wire to be installed.
One example of a non-isolated system is an automotive system, such as both batteries are negative and connected to the chassis of a vehicle. The system is non-isolated but either unit will suit.
The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to °C with a full rated output up to 40°C.
NEED TO CALCULATE MPPT USE THE HANDY TOOL BELOW
Australian Owned & Operated
Designed for Off Road and Heavy Duty Applications
Perfect for use in caravans, marine, camping and home storage off grid applications. Solar, wind or battery charger compatible. Designed to handle the vibration when off road.
Reliable 12V Power
Campers appreciate being able to charge multiple devices simultaneously while enjoying a peaceful camping experience.
Portable Power Solutions
Superior Versatility: This MPPT is ideal for 4WDs, caravans, RVs, trucks, campers, trailers, campervans, commercial vehicles and boats.
Easy to Use and Setup
This plug-and-play device is so user-friendly that anyone can set it up. Multiple Protection: Over-charge, short circuit, over-temperature, over-voltage, solar input overload and reverse polarity protection are incorporated.
For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
For lithium batteries absorption time is fixed, default 2 hours.
Alternatively, a fixed output voltage can be chosen.
Welcome to our website. If you continue to browse and use this website, you are agreeing to comply with and be bound by the following terms and conditions of use, which together with our privacy policy govern Aussie Batteries & Solar’s relationship with you in relation to this website. If you disagree with any part of these terms and conditions, please do not use our website.
The term ‘Aussie Batteries & Solar’ or ‘us’ or ‘we’ refers to the owner of the website whose registered office is . Our ABN is 51 640 926 718. The term ‘you’ refers to the user or viewer of our website.
The use of this website is subject to the following terms of use:
The content of the pages of this website is for your general information and use only. It is subject to change without notice.
Neither we nor any third parties provide any warranty or guarantee as to the accuracy, timeliness, performance, completeness or suitability of the information and materials found or offered on this website for any particular purpose. You acknowledge that such information and materials may contain inaccuracies or errors and we expressly exclude liability for any such inaccuracies or errors to the fullest extent permitted by law.
Your use of any information or materials on this website is entirely at your own risk, for which we shall not be liable. It shall be your own responsibility to ensure that any products, services or information available through this website meet your specific requirements.
This website contains material which is owned by or licensed to us. This material includes, but is not limited to, the design, layout, look, appearance and graphics. Reproduction is prohibited other than in accordance with the copyright notice, which forms part of these terms and conditions.
All trademarks reproduced in this website, which are not the property of, or licensed to the operator, are acknowledged on the website.
Unauthorised use of this website may give rise to a claim for damages and/or be a criminal offence.
From time to time, this website may also include links to other websites. These links are provided for your convenience to provide further information. They do not signify that we endorse the website(s). We have no responsibility for the content of the linked website(s).
Your use of this website and any dispute arising out of such use of the website is subject to the laws of Australia.
-Isolated-DC-DC-Charger_03_1200x1200.jpg)
.png)
.png)
REMOTE ON/OFF 
.png)
.png)
Designed for Off Road and Heavy Duty Applications
.png)
